Simple Coil on Plug Tester
I had an extra crank sensor so I made a quickie COP tester Just 3D printed a cap with a phono jack on top I would have used a BNC…
3D Printing
Another Drill Press
Not that I neded another drill press but I got this one at a yard sale for $5 I 3d printed some endcaps for an old servo motor and added…
My Temu Light Quit So…..
I liked this little $7 light from Temu but it quickly failed. Firest one channel went to full on then the motor stopped and finally the remote quit doing anything….…
OBDII Breakout Box
I’ve never really “needed” one but if I can make it for less than $20 why not….. And with the extra connector it doubles as a Tee
Dalek Eye Stalks
I have to finish these Dalek Eye Stalks. I was supposed to use them last halloween but I never got around to finishing them. They are ready to be screwed…
Midi Drum Machine
I saw this project from Volos’ youtube channel and had to try it. I dont have the midi synthesizer module but I was just working on a Yamaha DB50XG so…
XBOX 360 RF Board Hack
My son asked me about connecting the RF board from a dead 360 to his PC. I went through the site he sent me and found some good info but…
FTDI Based Programmer Box
I have used bare ftdi boards to program chips for a while but every now and then i end up shorting the bottom against something. I decided to make this…
Tube Notcher Templates
While watching South Main Auto, my favorite youtube channel, I saw a Eric O use a windows program called tubemiter to produce a printed template for notching a tube. I…
DDS VFO for the DX-60a
I got this CB VFO at a hamfest for $2. Perfect case for a DDS VFO.. First thing was to gut it and save all the bits, especially the gear…
Upgrade to an old Cantenna Dummy Load
A few years go I made a Cantenna Dummy load. I filled it with mineral oil left over from some woodworking projects and it;s worked great for a long time.…
Nerf Chronograph
I saw this on instructables and had to try it… Luckily there are plenty of Nerf guns in this house…. I had a sensor amplifier board on the bench from…
Temperature Sensor for the CO2 Laser Cutter
More K40 Mods.....
A Display Panel for my CO2 Laser
A Display Panel for a K40 CO2 Laser
Loose Power Plugs on my K40 plus Lights & Air Assist Nozzle
I noticed the manufacturer tried to hot glue the mains jacks in place. Really shoddy. So I 3D printed a locking frame… Since I only needed one power outlet I…
More CO2 Laser Water Pump Features
So far the new water pump has been working great. I decided to add a water level cutoff switch. I used a two step switch so I would get a…
CO2 Laser Crosshairs
I do most of my engraving using a center origin. Its so easy to line up on a cnc machine with a nice pointy bit. Not so easy on the…
3D Printing a Cover for a Broken Honda Fuel Pump
I cant believe how ofter I 3D print a part. Every couple of days I make some small part. Sometimes its a cone shaped washer for a switch or a…
Upgrading a K40 for Engraving
I decided to swap my K40 controller for a GERBIL from awesome.tech. I considered the Cohesion 3D too. I’ve been using GRBL CNC controller with a few custom tweaks to…
Fuel Injector Tester
Time to sort through all the spare fuel injection parts in the garage This was one of the nicest looking but worst running Corvette intakes…. Speeduino may let me salvage…
Speeduino on a Briggs V-Twin
Before I take my chances with a real car I figured I’d test things on a garden tractor. I have a spare Briggs V-Twin for my tractor so I decided…
3D Printed Housing for an ASPX Air Fuel Gauge
I wanted a portable case for my ASPX Gauge. I don’t plan on keeping it in just one car but instead using it as a portable tuning meter. I made…
MPX4250 Cap for Speeduino Boards
One of the little annoyances for me on the older rev speeduino boards was the MPX sensor. It’s half cut screw posts made it fit so sloppy. I made a…
Custom Speeduino Trigger Wheel
I’ve been using these SeaDoo 36-2 trigger wheels I though I’d try to copy the ford 36-1 Wheel for use on an old Bolens Tractor I want to “update” So…
Blynk Board IOT
I wanted to use a Sparkfun Blynk Board for a remote temperature sensor. I made a little shield. luckily the pin spacing matches a protoboard. And I 3D printed a…