{"id":1317,"date":"2016-03-16T03:04:40","date_gmt":"2016-03-15T13:04:40","guid":{"rendered":"http:\/\/commons.pratt.edu\/open-source\/?p=864"},"modified":"2016-03-16T03:04:40","modified_gmt":"2016-03-15T13:04:40","slug":"repairing-a-camera-mount","status":"publish","type":"post","link":"https:\/\/www.kornequipped.com\/blog\/?p=1317","title":{"rendered":"Repairing a Camera Mount"},"content":{"rendered":"\n<p>I had a camera ceiling mount snap from being over tightened. I tried epoxy but that didn&#8217;t work&#8230;..<\/p>\n\n\n\n<figure class=\"wp-block-image\"><img decoding=\"async\" src=\"https:\/\/es.pratt.edu\/Commons\/Images\/3d_tips\/camera%20mount\/IMG_1217.JPG\" alt=\"\" \/><\/figure>\n\n\n\n<p>I had used a thread library before to make pipe fittings so I thought I&#8217;d give it a try. I just measured the threads and whats left of the collar.<\/p>\n\n\n\n<figure class=\"wp-block-image\"><img decoding=\"async\" src=\"https:\/\/es.pratt.edu\/Commons\/Images\/3d_tips\/camera%20mount\/IMG_1218.JPG\" alt=\"\" \/><\/figure>\n\n\n\n<p>I decided to make it a bit larger to make it easier to grip. But then again that&#8217;s what started this problem&#8230;..<\/p>\n\n\n\n<figure class=\"wp-block-image\"><img decoding=\"async\" src=\"https:\/\/es.pratt.edu\/Commons\/Images\/3d_tips\/camera%20mount\/IMG_1219.JPG\" alt=\"\" \/><\/figure>\n\n\n\n<p>Not bad.<\/p>\n\n\n\n<figure class=\"wp-block-image\"><img decoding=\"async\" src=\"https:\/\/es.pratt.edu\/Commons\/Images\/3d_tips\/camera%20mount\/IMG_1220.JPG\" alt=\"\" \/><\/figure>\n\n\n\n<p>Since I already replaced the mount I may remove the stalk and use it as a ceiling hugger for a new install&#8230;..<\/p>\n\n\n\n<figure class=\"wp-block-image\"><img decoding=\"async\" src=\"https:\/\/es.pratt.edu\/Commons\/Images\/3d_tips\/camera%20mount\/IMG_1221.JPG\" alt=\"\" \/><\/figure>\n\n\n\n<blockquote class=\"wp-block-quote is-layout-flow wp-block-quote-is-layout-flow\">\n<pre class=\"wp-block-preformatted\">\/\/****************************************************************\n\/\/* Name : Camera Mount Top                                      *\n\/\/* Author : Robert Joseph Korn                                  *\n\/\/* Notice : Copyright (c) 2016 Open Valley Consulting Corp      *\n\/\/* : All Rights Reserved                                        *\n\/\/* Date : 3\/5\/16                                                *\n\/\/* Version : 1.0                                                *\n\/\/* Notes :                                                      *\n\/\/****************************************************************\n\ninclude &lt;polyScrewThread.scad&gt;\n\ndifference(){\n\n     cylinder(d=26, h=15, $fn=20, center=true);\n\n     union () {\n          translate([0,0,-3])screw_thread(18,1.5,55,20,PI\/2,2);\n          cylinder(d=14, h=100, center=true);\n     }\n}<\/pre>\n<\/blockquote>\n","protected":false},"excerpt":{"rendered":"<p>I had a camera ceiling mount snap from being over tightened. I tried epoxy but that didn&#8217;t work&#8230;.. I had used a thread library before to make pipe fittings so I thought I&#8217;d give it a try. I just measured the threads and whats left of the collar. I decided to make it a bit [&hellip;]<\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[3],"tags":[],"class_list":["post-1317","post","type-post","status-publish","format-standard","hentry","category-3d-printing"],"_links":{"self":[{"href":"https:\/\/www.kornequipped.com\/blog\/index.php?rest_route=\/wp\/v2\/posts\/1317","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.kornequipped.com\/blog\/index.php?rest_route=\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.kornequipped.com\/blog\/index.php?rest_route=\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.kornequipped.com\/blog\/index.php?rest_route=\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.kornequipped.com\/blog\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=1317"}],"version-history":[{"count":0,"href":"https:\/\/www.kornequipped.com\/blog\/index.php?rest_route=\/wp\/v2\/posts\/1317\/revisions"}],"wp:attachment":[{"href":"https:\/\/www.kornequipped.com\/blog\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=1317"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.kornequipped.com\/blog\/index.php?rest_route=%2Fwp%2Fv2%2Fcategories&post=1317"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.kornequipped.com\/blog\/index.php?rest_route=%2Fwp%2Fv2%2Ftags&post=1317"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}